JK: Factory Replacement CV Joint Kit - High-Angle Rzeppa
JK: Factory Replacement CV Joint Kit - High-Angle Rzeppa.
- - The TeraFlex JK: Factory Replacement High-Angle Rzeppa CV Joint Kit replaces a worn or damaged factory Rzeppa CV joint and driveshaft without resorting to an expensive aftermarket U-joint upgrade.
- - Quality components for years of service
- - Installation tool included
- - High-viscosity, surface bonding, low friction grease included
Fitment and Installation Notes
- - Grease MUST be packed thoroughly and liberally to the entire CV assembly.
- - Not compatible with axle end of front driveshaft
Description
JK: Factory Replacement CV Joint Kit - High-Angle Rzeppa.
- - The TeraFlex JK: Factory Replacement High-Angle Rzeppa CV Joint Kit replaces a worn or damaged factory Rzeppa CV joint and driveshaft without resorting to an expensive aftermarket U-joint upgrade.
- - Quality components for years of service
- - Installation tool included
- - High-viscosity, surface bonding, low friction grease included
Fitment and Installation Notes
- - Grease MUST be packed thoroughly and liberally to the entire CV assembly.
- - Not compatible with axle end of front driveshaft
JK: Factory Replacement CV Joint Kit - High-Angle Rzeppa.
The TeraFlex JK: Rzeppa High-Angle Factory Replacement CV Joint Kit replaces a worn or damaged factory Rzeppa CV joint and driveshaft without resorting to an expensive aftermarket U-joint upgrade. Allows angles up to 15 degrees. The high-angle CV housing reduces boot failure associated with 3" or more lift. The included low-friction grease is engineered specifically for the high RPM needs of the JK Rzeppa CV joint and features high-viscosity surface bonding characteristics necessary to properly adhere the grease to all moving surfaces.
The TeraFlex JK: Factory Replacement High-Angle Rzeppa CV Joint Kit replaces a worn or damaged factory Rzeppa CV joint and driveshaft without resorting to an expensive aftermarket U-joint upgrade.
Fitment and Installation Notes
- - Direct replacement
- - Quality components for years of service
- - Installation tool included
- - High-viscosity, surface bonding, low friction grease included
- - Use existing drive shaft, replaces the Rzeppa joint only
- - Fitment: JK Wrangler (2-door)
- - Fitment: JKU Wrangler Unlimited (4-door)
- - Fitment: Not compatible with axle end of front driveshaft
- - Height: 5
- - Installation Time: 1 hour
- - Length: 9
- - Product Image Size: Default
- - Note: Proper grease packing is crucial for joint longevity. Grease MUST be packed thoroughly and liberally to the entire CV assembly. Be generous and use all grease provided. Improperly packing the bearings with out enough grease will result in bearing failure.
- - Note: For complete step-by-step procedure please watch the instructional video.
- - Featured: No
- - Width: 5
WARNING: This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov/product
SAEJ2492 WARNING: By installing this product, you acknowledge that the suspension of this vehicle has been modified. As a result, this vehicle may handle differently than factory-equipped vehicles. As with any vehicle, extreme care must be used to prevent loss of control or rollover during sharp turns or abrupt maneuvers. Always wear seat belts, and drive safely, recognizing that reduced speeds and specialized driving techniques may be required. Failure to drive this vehicle safely may result in serious injury or death. Do not drive this vehicle unless you are familiar with its unique handling characteristics and are confident of your ability to maintain control under all driving conditions. Some modifications (and combinations of modifications) are not recommended and may not be permitted in your state. Consult your owner's manual, the instructions accompanying this product, and state laws before undertaking these modifications. You are responsible for the legality and safety of the vehicle you modify using these components.
ADDITIONAL SERVICES & COSTS MAY BE REQUIRED
INSTALLATION ALIGNMENT NOTE
Your vehicle may require a wheel alignment following installation to ensure proper handling and tire wear.
Additional alignment costs may apply.
INSTALLATION HEADLAMP AIM NOTE
Headlamp aim and alignment must be checked and adjusted as necessary following installation to help ensure proper visibility and the safety of other drivers.
Additional headlamp adjustment costs may apply.
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS) NOTE
If your vehicle is equipped with active or passive safety, collision monitoring, or driver assistance systems, these systems must be checked and adjusted as necessary following installation.
This includes, but is not limited to, camera-based and radar-based systems that may be affected by changes in vehicle ride height or suspension geometry.
Some vehicles may require OEM diagnostic equipment and factory-trained technicians to properly recalibrate ADAS functions.
Additional ADAS calibration costs may apply.
Have a certified mechanic do it for you!
installation_video=https://www.youtube.com/embed/gxw_iO9zuRM

