JL: 70" CRD60 HD Rear Axle with Full-Float (0-6" Lift), Delta Brakes (Coilover Brackets).

Engineered to integrate seamlessly with TeraFlex JL Coilover Kits, this axle is a true direct bolt-on solution. It features integrated Coilover Mount Brackets, bump-stop strike pads, high-clearance lower control arm brackets, and reinforced upper control arm mounts to handle the increased loads and articulation of a TeraFlex/Falcon Coilover Suspension System.

Available with Super 60 ring & pinion gear ratios of 4.30, 4.88, or 5.38, this 70" wide axle bolts directly into all JL models equipped with a TeraFlex Coilover System - eliminating the fabrication and guesswork typically associated with axle upgrades. Features/Benefits (bullet point) Full-float rear axle design for maximum strength and durability Designed specifically for TeraFlex JL Coilover Suspension Systems Integrated Coilover Mount brackets Bump-stop Strike Pad bracket High-clearance Lower Control Arm brackets Reinforced Upper Control Arm brackets

Turn-key axle solution for the Coilover-equipped JL Available with 4.30, 4.88, or 5.38 Super 60 gearing 3.25" O.D. x 0.375" wall DOM axle tube for superior strength vs. weight 70" WMS-WMS and 8x6.5" wheel bolt pattern Fixed spindle mount hub assembly Tera CRD60 specific high-pinion rear axle housing design Includes 1350 series pinion yoke 35-spline inner and outer axle shafts HD bearing caps increase rigidity and reduce ring & pinion distortion Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle

Built-in skimmer cuts ring gear oil halo and forces it into the pinion bearings Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing Oversized outer pinion bearing handles increased torque and high-load conditions High-capacity housing holds maximum amount of oil Pre-installed inner axle seals Ductile cast iron housing with increased rib gussets HD ductile iron differential cover with increased cover mounting area Integrated lower control arm skid plates High-flow oil passages

Reinforced rear track bar mount with multiple mounting locations UV protected triple-stage powder coat for corrosion resistance 1/4"-thick CNC laser cut axle brackets for extreme strength Pre-installed upper control arm bushings Proper pinion angle and raised track bar bracket for lifted JL applications Pre-drilled holes for limit straps and lower spring retainers Retains all JT ESP, ABS, and speedometer sensor capability 100% engineered, designed, and built in the USA with new components 1-Year/Unlimited Mileage Warranty

The Tera CRD60 HD Rear Coilover Full-Float Axle Assembly is designed as a direct bolt-on for the TeraFlex Coilover System and is available with pre-installed Super 60 gears, an ARB air locker, full-float axle shafts, and sensors.

Fitment and Installation Notes

• - Vehicle fitment info:
• - All JL Wranglers with TeraFlex Coilover suspension
• - 0-6" Lift
• - Product Notes:
• - Specs:
• - WMS-WMS: 70"
• - Axle Tube: 3.25" x 0.375"
• - Wheel Bolt Pattern: 8x6.5"
• - Includes Rear Delta Brake Kit

WARNING: This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov/product

SAEJ2492 WARNING: By installing this product, you acknowledge that the suspension of this vehicle has been modified. As a result, this vehicle may handle differently than factory-equipped vehicles. As with any vehicle, extreme care must be used to prevent loss of control or rollover during sharp turns or abrupt maneuvers. Always wear seat belts, and drive safely, recognizing that reduced speeds and specialized driving techniques may be required. Failure to drive this vehicle safely may result in serious injury or death. Do not drive this vehicle unless you are familiar with its unique handling characteristics and are confident of your ability to maintain control under all driving conditions. Some modifications (and combinations of modifications) are not recommended and may not be permitted in your state. Consult your owner's manual, the instructions accompanying this product, and state laws before undertaking these modifications. You are responsible for the legality and safety of the vehicle you modify using these components.